Quality Control of Head Cylinder Products Using the Seven Tools Approach at PT Otomotif Indonesia
DOI:
https://doi.org/10.24014/jti.v10i2.32000Abstract
PT Otomotif Indonesia is a Japanese manufacturing company. Company management continues to strive to improve the quality of products produced, including cylinder heads. Quality control is something that needs to be done in a company to minimise the occurrence of defective goods. The research was conducted in the machining section of the cylinder head manufacturing process. The highest cylinder head production percentage was 0.88% in November 2023. This research aims to minimise the occurrence of defects by applying the Seven Tools method. Seven Tools is a methodology consisting of seven quality control instruments: Check Sheet, Stratification, histogram diagram, Pareto diagram, scatter diagram, control chart, and Fishbone diagram. After data processing using the seven tools method, 5 errors were identified, the biggest being pen-matching errors. The 5W+1H method was used when analysing the Fishbone diagram and making recommendations for improvement.
Keywords: Quality Control, Cylinder Head, Seven Tools
References
A.Wicaksono andF.Yuamita, “Pengendalian Kualitas Produksi Sarden Mengunakan Metode Failure Mode and Effect Analysis (FMEA) Untuk Meminimumkan Cacat Kaleng Di PT. Maya Food Industries,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, pp. 1–6, 2022, doi: https://doi.org/10.55826/tmit.v1iI.6.
A.Anastasya andF.Yuamita, “Pengendalian Kualitas Pada Produksi Air Minum Dalam Kemasan Botol 330 ml Menggunakan Metode Failure Mode Effect Analysis (FMEA) di PDAM Tirta Sembada,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. I, pp. 15–21, 2022, doi: https://doi.org/10.55826/tmit.v1iI.4.
D.Chandrahadinata andW.Nurdiana, “Analisis Pengendalian Kualitas Pada Crude Palm Oil untuk Meningkatkan Kualitas di PT. Condong Garut,” J. Kalibr., vol. 19, no. 1, pp. 43–52, 2022, doi: 10.33364/kalibrasi/v.19-1.1045.
I.Andespa, “Analisis Pengendalian Mutu Dengan Menggunakan Statistical Quality Control (Sqc) Pada Pt.Pratama Abadi Industri (Jx) Sukabumi,” E-Jurnal Ekon. dan Bisnis Univ. Udayana, vol. 2, p. 129, 2020, doi: 10.24843/eeb.2020.v09.i02.p02.
B.Septiana andB.Purwanggono, “Analisis Pengendalian Kualitas Dengan Menggunakan Failure Mode Error Analysis (Fmea) Pada Divisi Sewing Pt Pisma Garment Indo,” Ejournal3.Undip.Ac.Id, 2018.
D.Rahmanasari, W.Sutopo, andJ. M.Rohani, “Implementation of Lean Manufacturing Process to Reduce Waste: A Case Study,” IOP Conf. Ser. Mater. Sci. Eng., vol. 1096, no. 1, p. 012006, 2021, doi: 10.1088/1757-899x/1096/1/012006.
A.Adyatama, N. U.Handayani, N. H.-J. ti U. J.Teknik, U.2018, andN. U.Handayani, “Perbaikan kualitas menggunakan prinsip kaizen dan 5 why analysis: studi kasus pada painting shop karawang plant 1, PT Toyota Motor Manufacturing Indonesia,” J@ ti Undip J. Tek. Ind., vol. 13, no. 3, pp. 169–176, 2018, Accessed: Jun.17, 2022. [Online]. Available: https://ejournal.undip.ac.id/index.php/jgti/article/view/21426
S.Bakhtiar, S.Tahir, andR. A.Hasni, “Analisa Pengendalian Kualitas Dengan Menggunakan Metode Statistical Quality Control (SQC),” Malikussaleh Ind. Eng. J., vol. 2, no. 1, pp. 29–36, 2013.
I.Wulandari andM.Bernik, “Penerapan Metode Pengendalian Kualitas Six Sigma Pada Heyjacker Company,” EkBis J. Ekon. dan Bisnis, vol. 1, no. 2, p. 222, 2018, doi: 10.14421/ekbis.2017.1.2.1008.
D. A.Hadiat, Handarto, andS.Nurjanah, “Analisis Pengendalian Mutu Produk Tempe Menggunakan Statistical Quality Control (SQC) di Industri Rumah Tangga Yayah Komariah, Majalengka,” Sent. 2019 Semin. Nas. Tek. Elektro 2019 , no. November 2019, pp. 376–387, 2019.
E.Haryanto, “Analisis Pengendalian Kualitas Produk Bos Rotor Pada Proses Mesin Cnc Lathe Dengan Metode Seven Tools,” J. Tek., vol. 8, no. 1, pp. 69–72, 2019, doi: 10.31000/jt.v8i1.1595.
D.Diniaty, “Analisis kecacatan produk tiang listrik beton menggunakan metode seven tools dan new seven tools (Studi Kasus: Pt. Kunango Jantan),” J. Tek. Ind. J. Has. Penelit. Dan Karya Ilm. Dalam Bid. Tek. Ind., vol. 2, no. 2, pp. 155–162, 2016.
S. A. A.Baraba et al., “Pengendalian Kualitas Produk dengan Penerapan Kaizen 5S dan Metode Seven Tools pada PT. Bali Es,” in Seminar dan Konferensi Nasional IDEC, 2021, pp. 2579–6429. Accessed: Jun.17, 2022. [Online]. Available: https://idec.ft.uns.ac.id/wp-content/uploads/IDEC2021/PROSIDING/LPSKE/ID008.pdf
S. S.Dahdah, “Pengendalian Kualitas Pengelasan Pada Konstruksi Mechanical Piping Dengan Metode Seven Tools,” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 9, no. 2, pp. 498–505.
J.Hardono, H.Pratama, andA.Friyatna, “Analisis Cacat Produk Green Tyre dengan Pendekatan Seven Tools,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 5, no. 1, p. 1, 2019, doi: 10.30656/intech.v5i1.1462.
R.Ratnadi andE.Suprianto, “Pengendalian Kualitas Produksi Menggunakan Alat Bantu Statistik (Seven Tools) Dalam Upaya Menekan Tingkat Kerusakan Produk,” J. Indept, vol. 6, no. 2, p. 11, 2016.
I.Nursyamsi andA.Momon, “Analisa pengendalian kualitas menggunakan metode seven tools untuk meminimalkan return konsumen di PT. XYZ,” J. Serambi Eng., vol. 7, no. 1, 2022.
A. Z.AlFaritsy andA. Z.AlFaritsy, “Analisis Pengendalian Kualitas Produk Ember Cat Tembok 5kg Menggunakan Metode New Seven Tools:(Studi Kasus: PT. X),” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. 3, pp. 231–242, 2022, [Online]. Available: http://jurnal-tmit.com/index.php/home/article/view/41
M.Iskhaq, H.Hidayat, andA. W.Rizqi, “Quality Control Analysis on Nylon Monofilament Net Production Process Using the Seven Tools Method and FMEA at PT ARIDA,” J. Serambi Eng., vol. 8, no. 4, pp. 7370–7378, 2023, doi: 10.32672/jse.v8i4.6900.
M. W. S.Aunillah, M. D.Kurniawan, andH.Hidayat, “Analisis Pengendalian Kualitas Produksi Batu Kumbung Menggunakan Metode Seven Tools (Studi Kasus: CV. Salsabilah Group),” Sigma Tek., vol. 5, no. 1, pp. 30–38, 2022.
A. L. N.Falah, K.Arief, andR. S.Riginianto, “Analisis Pengendalian Kualitas Pada Tempe Menggunakan Metode Seven Tools Dan FMEA,” … Manaj. Ind. Terap., 2023, [Online]. Available: http://jurnal-tmit.com/index.php/home/article/view/264
R. V.Zendrato, R.Ryantama, M. A.Nugroho, D.Putri, D.Kuncoro, andS.Parningotan, “Analisis Pengendalian Kualitas Pada Tempe Menggunakan Metode Seven Tools,” IMTechno J. Ind. Manag. Technol., vol. 3, no. 2, pp. 99–109, 2022.
S.Somadi, B. S.Priambodo, andP. R.Okarini, “Evaluasi Kerusakan Barang dalam Proses Pengiriman dengan Menggunakan Metode Seven Tools,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 6, no. 1, pp. 1–11, 2020, doi: 10.30656/intech.v6i1.2008.
N. A.Pratama, M. Z.Dito, O. O.Kurniawan, andA. Z.Al-Faritsy, “Analisis Pengendalian Kualitas Dengan Metode Seven Tools Dan Kaizen Dalam Upaya Mengurangi Tingkat Kecacatan Produk,” J. Teknol. dan Manaj. Ind. Terap., vol. 2, no. 2, pp. 53–62, 2023.
A.Prasetiyo, W.Safitri, andF.Fathurohman, “Analisis Pengendalian Kualitas Produk Dengan Metode Seven Tools (Studi Kasus Line Rocker Arm N2J Pt. Xxx Cikarang Indonesia),” in Prosiding Seminar Sosial Politik, Bisnis, Akuntansi dan Teknik, 2022, pp. 108–117.
K.Damayanti, M.Fajri, andN.Adriana, “Pengendalian Kualitas Di Mabel PT. Jaya Abadi Dengan Menggunakan Metode Seven Tools,” Bull. Appl. Ind. Eng. Theory, vol. 3, no. 1, 2022.
J.Radianza andI.Mashabai, “Analisa Pengendalian Kualitas Produksi Dengan Menggunakan Metode Seven Tools Quality Di PT. Borsya Cipta Communica,” JITSA J. Ind. Teknol. Samawa, vol. 1, no. 1, pp. 17–21, 2020.
Downloads
Published
Issue
Section
License
Authors who publish with Jurnal Teknik Industri: Jurnal Hasil Penelitian dan Karya Ilmiah dalam Bidang Teknik Industri agree to the following terms:
1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (CC BY-NC-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).