Analisis Faktor Pengendalian Tingginya Kadar Air Pada Produksi Crude Palm Oil Melalui Pendekatan SPC dan FMEA Di PT Socfindo Seunagan
DOI:
https://doi.org/10.24014/sitekin.v19i2.17817Abstract
PT. Socfindo Seunagan is a company unit of PT. Socfindo Indonesia which is engaged in oil palm plantations and processing of oil palm fruit or Fresh Fruit Bunches into Crude Palm Oil. Based on observations made at PT. Socfindo Seunagan, the type of damage that most dominates the decline in CPO quality is high water content which is not in accordance with the standards set by the company, namely 0.5%. The purpose of this study was to identify the factors that cause high water content in CPO products using the FMEA method and control using the SPC method. The results of the FMEA method obtained that the highest Risk Priority Number (RPN) value for 9 factors caused the vacuum dryer machine not to operate properly at 567. Through the SPC method, it was found that the influence of these causal factors had a percentage of 29% of the other 8 factors. Based on the determination of the control chart, the center line is 243, the upper control line is 745 and the lower control line is -260. This indicates that the causative factors have a major influence on the high water content of CPO. From the fishbone diagram the vacuum dryer machine does not operate properly due to human factors, machine factors, materials and method factors.References
R. Harahap, “Pengaruh Kualitas Produk Terhadap Kepuasan Pelanggan Di Restoran Cepat Saji Kfc Cabang Asia Mega Mas Medan,” Manaj. Tools, vol. 7, no. 1, pp. 77–84, 2017.
M. Rizki et al., “Aplikasi End User Computing Satifaction pada Penggunaan E-Learning FST UIN SUSKA,” ejournal.uin-suska.ac.id, vol. 19, no. 2, pp. 154–159, 2022, Accessed: Jun. 05, 2022. [Online]. Available: http://ejournal.uin-suska.ac.id/index.php/sitekin/article/view/14730.
A. T. P. Sunardi and E. Suprianto, “Pengendalian Kualitas Produk Pada Proses Produksi Rib A320 Di Sheet Metal Forming Shop,” Indept, vol. 5, no. 2, pp. 6–15, 2015.
N. Nurzam, R. S. Fauziah, and K. C. Susena, “Pegaruh Harga Dan Kualitas Produk Terhadap Keputusan Petani Membeli Bibit Sawit Di Pt. Bio Nusantara Teknologi Bengkulu,” EKOMBIS Rev. J. Ilm. Ekon. dan Bisnis, vol. 8, no. 1, pp. 79–89, 2020, doi: 10.37676/ekombis.v8i1.934.
S. Widiyawati and S. Assyahlafi, “Perbaikan Produktivitas Perusahaan Rokok Melalui Pengendalian Kualitas Produk dengan Metode Six Sigma,” J. Ind. Eng. Manag., vol. 2, no. 2, p. 32, 2017, doi: 10.33536/jiem.v2i2.150.
Susriyati, M. I. Adelino, and R. G. Solasyo, “Analisis Kehilangan Minyak (Oil Losses) Stasiun Press Menggunakan Metode Statistical Process Control (SPC),” J. Ekobistek, vol. 10, no. 2, pp. 146–150, 2021, doi: 10.35134/ekobistek.v10i2.116.
I. Septiawan, M. S. Ningsih, and I. Gunawan, “Analisis pengendalian kualitas pada Crude Palm Kernel Oil dengan metode Six Sigma di PT. X,” J. Vor., vol. 3, no. 1, pp. 166–173, 2022, doi: 10.54123/vorteks.v3i1.153.
M. Nur, Y. E. P. Dasneri, and A. Masari, “Pengendalian Kualitas Crude Palm Oil (CPO) di PT. Sebanga Multi Sawit,” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 5, no. 2, p. 148, 2020, doi: 10.24014/jti.v5i2.8985.
D. Vera and Marwiji, “Analisis Kehilangan Minyak pada Crude Palm Oli (CPO) dengan Menggunakan Metode Statistical Process Control,” J. Ilm. Tek. Ind., vol. 13, no. 1, pp. 28–42, 2017.
H. Anbar Fadhilah, “Analisa Pengendalian Kualitas Produk Packaging Karton Box PT. X dengan Menggunakan Metode Statistical Quality Control,” Serambi Eng., vol. VII, no. 2, pp. 2948–2953, 2022.
A. Wicaksono and F. Yuamita, “Pengendalian Kualitas Produksi Sarden Mengunakan Metode Failure Mode and Effect Analysis (FMEA) Untuk Meminimumkan Cacat Kaleng Di PT. Maya Food Industries,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, pp. 1–6, 2022, doi: https://doi.org/10.55826/tmit.v1iI.6.
B. N. Abdallah, Muqimuddin, and R. Lazawardi, “Peningkatan Karakteristik Kualitas Palm Kernel Oil ( PKO ) Menggunakan Metodologi Six Sigma,” J. Sains, Teknol. dan Ind., vol. 19, no. 01, pp. 81–89, 2021.
A. Anastasya and F. Yuamita, “Pengendalian Kualitas Pada Produksi Air Minum Dalam Kemasan Botol 330 ml Menggunakan Metode Failure Mode Effect Analysis (FMEA) di PDAM Tirta Sembada,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, pp. 15–21, 2022, doi: https://doi.org/10.55826/tmit.v1iI.4.
M. Rizki, A. Wenda, … F. P.-2021 I., and undefined 2021, “Comparison of Four Time Series Forecasting Methods for Coal Material Supplies: Case Study of a Power Plant in Indonesia,” ieeexplore.ieee.org, Accessed: Jun. 05, 2022. [Online]. Available: https://ieeexplore.ieee.org/abstract/document/9493522/.
A. Ridwan and N. A. Savitri, “Pengendalian Mutu Inventory Loss Bahan Baku Utama Pakan Ternak Dengan Metode Statistical Process Control (Spc),” J. Ind. Serv., vol. 5, no. 2, pp. 168–174, 2020, doi: 10.36055/jiss.v5i2.7995.
A. Muarif et al., “Analisis Kualitas Crude Palm Oil (CPO) Berdasarkan Kinerja Vacuum Dryer Di PKS Koperasi Primajasa.”
R. I. Yaqin, Z. Z. Zamri, J. P. Siahaan, Y. E. Priharanto, M. S. Alirejo, and M. L. Umar, “Pendekatan FMEA dalam Analisa Risiko Perawatan Sistem Bahan Bakar Mesin Induk: Studi Kasus di KM. Sidomulyo,” J. Rekayasa Sist. Ind., vol. 9, no. 3, pp. 189–200, Oct. 2020, doi: 10.26593/jrsi.v9i3.4075.189-200.
A. Salonen and M. Deleryd, “Cost of poor maintenance: A concept for maintenance performance improvement,” J. Qual. Maint. Eng., vol. 17, no. 1, pp. 63–73, 2011, doi: 10.1108/13552511111116259.
A. Ramdani, M. Satori, and N. R. As’ ad, “Perbaikan Kualitas pada Produk Pembuatan Tas Backpack Menggunakan Metode Statistical Quality Control (SQC) dan Failure Mode And Effect Analysis (FMEA),” pp. 9–17, 2020
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License
Copyright Notice
An author who publishes in the SITEKIN Journal agrees to the following terms:
- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal
- Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgement of its initial publication in this journal.
- Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See The Effect of Open Access).
Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.
