Pemilihan Material Yang Aman Untuk Frame Sepeda Listrik
DOI:
https://doi.org/10.24014/sitekin.v20i1.19985Abstract
Material properties or often referred to as mechanical properties are properties of materials related to behavior towards mechanical loading. Mechanical properties are necessary in considering the selection of materials that correspond to the circumstances required at loading. In addition to mechanical properties, dimensions are also needed that have a large role in assessing the strength of a bicycle frame. In this study, a material selection analysis process will be carried out based on the stress, displacement and safety factoe on the bicycle frame. The materials used in this study were aluminum 6061, steel and carbon with variations in loading of 60kg, 75kg, and 90kg. The analysis process is carried out using Autodesk inventor software. Where from the results of the 2018 Inventor software analysis obtained the value of von misses stress, displacement and safety factors. The conclusion obtained in this study is that the highest load has a maximum voltage owned by aluminum material 6061 and the displacement is the largest owned by carbon material. Safety factor worth more than 1 is owned by all materials, namely aluminum 6061, carbon and steel so that all materials are safe to use as electric bicycle frames.
References
B. O. Lobo, “Sifat Mekanik pada sambungan Las Dissimilar SMAW antara Baja St 42 dan SS AISI 304,” 2018.
I. H. Ramadhan, S. Herbirowo, B. Adjiantoro, and Sunardi, “Karakteristik Sifat Mekanik Dan Struktur Mikro Pada Baja Laterit Dengan Proses Cold Rolling,” Jurnal Teknologi Bahan dan Barang Teknik, vol. 9, no. 1, p. 33, Jun. 2019, doi: 10.37209/jtbbt.v9i1.88.
I. Saefuloh, A. Pramono, W. Jamaludin, I. Rosyadi, and Haryadi, “Studi Karakterisasi Sifat Mekanik Dan struktur Mikro Material Piston Alumunium-Silikon Alloy,” 2018. [Online]. Available: http://jurnal.untirta.ac.id/index.php/jwl
Salimin, Samhuddin, and I. Adha, “Perancangan dan Analisa Simulasi Pembebanan Chassis Sepeda Wisata Untuk Dua Penumpang Menggunakan Software Autodesk Inventor 2017,” vol. 3, no. 3, 2018.
A. M. Hidayat, E. G. Pramono, and R. Waluyo, “Perancangan Dan Simulasi Desain Rangka Sepeda Motor Listrik Tipe Trellis Menggunakan Finite Element Metode (FEM),” vol. 4, no. 2, 2022.
A. Suwandi, A. D. Cahyo, and D. Dahlan, “Manufaktur Konstruksi Rangka Sepeda Motor Listrik Kapasitas 3 kW,” SEMRESTEK, pp. 679–685, 2018.
L. F. Nurulhadi and R. Hanifi, “Analisis Kekuatan dan Desain Frame Mini Bike 20 Inch menggunakan Pendekatan Finite Elemen Method (FEM),” Ilmiah Wahana Pendidikan, vol. 8, no. 7, pp. 362–367, 2022.
B. H. Andre and A. A. Nur, “Rancang Bangun Mesin CNC Router 3 Axis Berbantu Perangkat Lunak Autodesk Inventor 2015,” Nozzle : Journal mechanical engineering, vol. 9, no. 2, pp. 31–37, 2020.
A. H. P. Ningtyas, Hidayat, and P. N. Rofiyanto, “Analisis desain frame sepeda listrik roda tiga sebagai alat bantu transportasi bagi penyandang disabilitas menggunakan software Autodesk Inventor,” Jurnal Teknik Mesin Indonesia, vol. 16, no. 2, pp. 7–11, 2021.
H. Isworo, A. Ghofur, and G. Rudi, “Analisis dissplacement pada chassis mobil listrik wasaka 1),” vol. 6, no. 2, pp. 94–104, 2019.
L. H. Al Ichlas Imran, Samhuddin, Salimin, “Perancangan, analisa dan simulasi rangka sepeda listrik untuk masyarakat perkotaan,” vol. 9, no. 2, pp. 0–6, 2018.
Sunardi, “Optimalisasi Desain Frame Sepeda Menggunakan Software Autodesk Inventor 2015,” vol. 20, no. 2, pp. 187–192, 2017.
B. Setyono and A. Hamid, “Perancangan Dan Analisis Kekuatan Frame Sepeda Hibrid ‘ Trisona ’ Menggunakan Software Autodesk Inventor,” vol. 20, no. 2, pp. 37–46, 2016.
B. Setyono and S. Gunawan, “Perancangan Dan Analisis Chassis Mobil Listrik ‘ Semut Abang ’ Menggunakan Software Autodesk Inventor PRO 2013,” pp. 69–78, 2015.
W. Jasiński, P. Krysiak, C. Pichlak, and K. Ludian, “Optimisation of a mobile device frame structure – practical aspects,” Technical Transactions, vol. 2022, no. 1, pp. 1–10, 2022, doi: 10.37705/techtrans/e2022001.
G. Tri Setiadanu, Y. Gunawan, G. Titanandana Andrayuga Pratama, and N. Qolbi, “Pemodelan Rangka Prototipe Sepeda Listrik Kargo Roda Tiga Multiguna,” Ketenagalistrikan dan Energi Terbarukan, vol. 19, no. 1, pp. 41–50, 2020.
M. Jufri Dullah and A. Kadir Muhammad, “Perancangan Sepeda Listrik Menggunakan Motor Bldc Dengan Penggerak Depan Untuk Area Perumahan,” in Prosiding 4th Seminar Nasional Penelitian & Pengabdian Kepada Masyarakat , 2020, pp. 90–96.
Ramadhan. Tatag Estuadi and Tristiyono. Bambang, “Design Requirements & Objectives Sepeda Listrik untuk Siswi Sekolah Menengah Melalui Riset Konsumen,” Sains Dan Seni ITS, vol. 8, no. 1, 2019.
M. R. Rinaldy, H. Poernomo, and T. A. Setiawan, “Desain Kendaraan Bermotor Roda Tiga Sebagai Alat Bantu Transportasi Bagi Penyandang Disabilitas,” Proceedings Conference on Design Manufacture Engineering and its Application, vol. 1, no. 1, pp. 55–59, 2018.
C. Wibowo, F. M. Dewadi, and A. Al-Afgani, “Implementasi Material Titanium Pada Sepeda Listrik Sebagai Rangka Yang Efisien,” Mechanical Xplore, vol. 2, no. 1, pp. 13–18, 2021, [Online]. Available: http://journal.ubpkarawang.ac.id/Index.php/JTMX
F. Toteles, Aris; Alhaffis, “Analisis Material Kontruksi Chasis Mobil Listrik Laksamana V2 Menggunakan Software Autodesk Inventor Program Studi Sarjana Terapan Teknik Mesin Produksi dan Perawatan , Jurusan Teknik Mesin , Politeknik Negeri Bengkalis Email : arishtoteles99@gmail.com 30,” Machine; Jurnal Teknik Mesin, vol. 7, no. 1, pp. 30–37, 2021.
M. S. D. Ellianto and Y. E. Nurcahyo, “Rancang Bangun dan Simulasi Pembebanan Statik pada Sasis Mobil Hemat Energi Kategori Prototype,” Jurnal Engine: Energi, Manufaktur, dan Material, vol. 4, no. 2, pp. 53–58, 2020.
F. A. Budiman, A. Septiyanto, S. Sudiyono, A. D. N. I. Musyono, and R. Setiadi, “Analisis Tegangan von Mises dan Safety Factor pada Chassis Kendaraan Listrik Tipe In-Wheel,” Jurnal Rekayasa Mesin, vol. 16, no. 1, p. 100, 2021, doi: 10.32497/jrm.v16i1.1997.
Andriyanto, G. T. Setiadanu, Slamet, Y. Gunawan, G. T. A. Pratama, and N. Qolbi, “Pemodelan Rangka Prototipe Sepeda Listrik Kargo Roda Tiga Multiguna,” Jurnal Ketenagalistrikan dan Energi Terbarukan, vol. 19, no. 1, pp. 41–50, 2020.
A. A. Attorik, Ambiyar, D. Y. Sari, and B. Rahim, “Simulasi Dan Analisis Kekuatan Pembebanan Frame Pada Perancangan Mesin Press Bearing Manual Hydraulic Jack Menggunakan Autodesk Inventor,” Journal homepage: http://vomek.ppj.unp.ac.id, vol. 4, no. 1, pp. 19–25, 2022
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License
Copyright Notice
An author who publishes in the SITEKIN Journal agrees to the following terms:
- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal
- Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgement of its initial publication in this journal.
- Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See The Effect of Open Access).
Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.
