Analysis of Quality Control Using the Failure Mode And Effect Analysis (FMEA) Method in the Welding Process in the Feed Drum Project
DOI:
https://doi.org/10.24014/sitekin.v20i2.21731Abstract
PT. Xyz is a steel fabrication company located in Gresik. One of their projects undertaken by PT. XYZ is a Feed drum Project, the welding process is the most important stage in this project. At the time of product testing or testing there were still many welding points that were defective so that the product did not pass the trial, the trial was carried out by hydrotest where this test was carried out with water as the test medium to determine the strength of a material and find out whether there was a leak or not and as well as a visual check. The types of defects found in the feed drum project are spatter, overlap, porosity, undercut, incomplete fusion, slag, bad String Bead (Weaving Fault), start stop, pin hole. The research uses the FMEA (Failure Mode Effects and Analysis) the method which aims to identify and analyze the occurrence of defects. In the results, the highest RPN value is found in the Incomplate Fusion type of defect with a value of 384 so that it becomes a priority in carrying out control and repair .
References
R. Ratnadi and E. Suprianto, “Pengendalian Kualitas Produksi Menggunakan Alat Bantu Statistik (Seven Tools) Dalam Upaya Menekan Tingkat Kerusakan Produk,” J. Indept, vol. 6, no. 2, p. 11, 2016, [Online]. Available: https://jurnal.unnur.ac.id/index.php/indept/article/view/178/0.
J. Hardono, H. Pratama, and A. Friyatna, “Analisis Cacat Produk Green Tyre dengan Pendekatan Seven Tools,” J. INTECH Tek. Ind. Univ. Serang Raya, vol. 5, no. 1, p. 1, 2019, doi: 10.30656/intech.v5i1.1462.
Z. Fatoni, M. L. King, and M. Lazim, “Perencanaan Desain Alat Bantu Temporary Clamp 8" Pada Pipe Line Industri Migas,” J. Desiminasi Teknol., vol. 9, 2021.
R. Y. Pratama, M. Basuki, and E. Pranata, “Pengaruh variasi arus pengelasan smaw untuk posisi pengelasan 1g pada material baja kapal ss 400 terhadap cacat pengelasan,” Jur. Tek. Perkapalan FTMK-ITATS, vol. 02, no. 1, pp. 203–209, 2020.
A. Khatammi and A. R. Wasiur, “Analisis Kecacatan Produk Pada Hasil Pengelasan Dengan Menggunakan Metode FMEA (Failure Mode Effect Analysis),” J. Serambi Eng., vol. 7, no. 2, pp. 2922–2928, 2022, doi: 10.32672/jse.v7i2.3853.
W. S. Nugroho, “Memperbaiki Hasil Pengelasan,” Buku Inf., pp. 1–67, 2018.
B. Septiana and B. Purwanggono, “Analisis Pengendalian Kualitas Dengan Menggunakan Failure Mode Error Analysis (Fmea) Pada Divisi Sewing Pt Pisma Garment Indo,” Ejournal3.Undip.Ac.Id, 2018, [Online]. Available: https://ejournal3.undip.ac.id/index.php/ieoj/article/view/22233.
Y. A. Fauzi and H. Aulawi, “Analisis Pengendalian Kualitas Produk Peci Jenis Overset Yang Cacat Di Pd. Panduan Illahi Dengan Menggunakan Metode Fault Tree Analysis (Fta) Dan Metode Failure Mode and Effect Analysis (Fmea)”,” J. Kalibr., vol. 14, no. 1, pp. 29–34, 2016, doi: 10.33364/kalibrasi/v.14-1.331.
A. Rahman, “Analisis Pengendalian Kualitas Produk Roti Tawar Mr . Bread Dengan Metode FMEA ( Di Bagian Produksi CV . Essen ),” J. Online Tek. Ind., vol. 1, no. 1, pp. 1–8, 2014.
M. Basori and S. Supriyadi, “Analisis Pengendalian Kualitas Cetakan Packaging Dengan Metode Failure Mode and Effect Analysis (FMEA),” Pros. Semin. Nas. Ris. Ter. SENASSET, pp. 158–163, 2017, [Online]. Available: https://e-jurnal.lppmunsera.org/index.php/senasset/article/view/442.
A. Wibowo, “Macam-Macam Cacat Las,” Macam Cacat Las, no. 109511414319, pp. 1–9, 2016.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License
Copyright Notice
An author who publishes in the SITEKIN Journal agrees to the following terms:
- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal
- Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgement of its initial publication in this journal.
- Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See The Effect of Open Access).
Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.
