The Influence Of The Work Environment On Employee Comfort Using The Method Failure Mode And Effect Analysis (FMEA)

Authors

  • Hanan Almeyda Hanesa Unisbank semarang
  • Endro Prihastono

DOI:

https://doi.org/10.24014/sitekin.v20i2.21770

Abstract

Employee performance is a very influential factor in the work system. Therefore, to reduce the wrong side of employee performance, it is necessary to have employee comfort and a work environment to improve a company’s quality and optimal performance. This study aims to analyze the effect of employee comfort and work environment on employee performance (at PT. Danwood Nusantara) using the methodFMEA (Failure Mode and Effect Analysis). The types of data used are primary data and secondary data. Data processing using the FMEA method, fishbone diagrams and productivity level calculations. The study results show that from the data obtained through interviews, three variables have a small value (must be corrected): comfort with lighting, room temperature, and noise. Data processing using the Results Analysis method Failure Mode and Effect Analysis (FMEA) shows that three types of work accidents have high RPN values: cutter scratches, pinched storage racks, and sprains when lifting goods. The productivity level in the warehouse is 0.99741 of the 16688 working hours that should have been lost due to work accidents 43 hours 10 minutes. The impact of work accidents can reduce employee productivity, thereby indirectly harming the company

References

M. Rizki et al., “Aplikasi End User Computing Satifaction pada Penggunaan E-Learning FST UIN SUSKA,” SITEKIN J. Sains, Teknol. dan Ind., vol. 19, no. 2, pp. 154–159, 2022, Accessed: Jun. 05, 2022. [Online]. Available: http://ejournal.uin-suska.ac.id/index.php/sitekin/article/view/14730.

A. Wicaksono and F. Yuamita, “Pengendalian Kualitas Produksi Sarden Mengunakan Metode Failure Mode And Effect Analysis (FMEA) Dan Fault Tree Analysis (FTA) Untuk Meminimalkan Cacat Kaleng Di PT XYZ,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. III, pp. 145–154, 2022.

A. Anastasya and F. Yuamita, “Pengendalian Kualitas Pada Produksi Air Minum Dalam Kemasan Botol 330 ml Menggunakan Metode Failure Mode Effect Analysis (FMEA) di PDAM Tirta Sembada,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. I, pp. 15–21, 2022, doi: https://doi.org/10.55826/tmit.v1iI.4.

A. S. M. Absa and S. Suseno, “Analisis Pengendalian Kualitas Produk Eq Spacing Dengan Metode Statistic Quality Control (SQC) Dan Failure Mode And Effects Analysis (FMEA) Pada PT. Sinar Semesta,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, no. III, pp. 183–201, 2022.

A. Wicaksono and F. Yuamita, “Pengendalian Kualitas Produksi Sarden Mengunakan Metode Failure Mode and Effect Analysis (FMEA) Untuk Meminimumkan Cacat Kaleng Di PT. Maya Food Industries,” J. Teknol. dan Manaj. Ind. Terap., vol. 1, pp. 1–6, 2022, doi: https://doi.org/10.55826/tmit.v1iI.6.

I. A. B. Nirwana, A. W. Rizqi, and M. Jufryanto, “Implementasi Metode Failure Mode Effect and Analisys (FMEA) Pada Siklus Air PLTU,” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 8, no. 2, pp. 110–118, 2022.

H. A. Yasin and R. P. Sari, “Pengembangan Sistem Inspeksi Digital Berbasis Macro VBA Excel Dengan Metode Failure Mode And Effects Analysis (FMEA),” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 7, no. 1, pp. 7–14.

W. Amalia, D. Ramadian, and S. N. Hidayat, “Analisis Kerusakan Mesin Sterilizer Pabrik Kelapa Sawit Menggunakan Failure Modes and Effect Analysis (FMEA),” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 8, no. 2, pp. 369–377, 2022.

C. S. Bangun, “Application of SPC and FMEA Methods to Reduce the Level of Hollow Product Defects,” J. Tek. Ind. J. Has. Penelit. dan Karya Ilm. dalam Bid. Tek. Ind., vol. 8, no. 1, pp. 12–16, 2022.

N. Tazi, E. Châtelet, and Y. Bouzidi, “Using a hybrid cost-FMEA analysis for wind turbine reliability analysis,” Energies, vol. 10, no. 3, p. 276, 2017.

Y. Hisprastin and I. Musfiroh, “Ishikawa Diagram dan Failure Mode Effect Analysis (FMEA) sebagai Metode yang Sering Digunakan dalam Manajemen Risiko Mutu di Industri,” Maj. Farmasetika, vol. 6, no. 1, p. 1, Oct. 2020, doi: 10.24198/mfarmasetika.v6i1.27106.

R. Y. Hanif, H. S. Rukmi, and S. Susanty, “Perbaikan kualitas produk keraton luxury di PT. X dengan menggunakan metode failure mode and effect analysis (FMEA) dan Fault Tree Analysis (FTA),” Reka Integr., vol. 3, no. 3, 2015.

I. S. Haq, A. Y. Darma, and R. A. Batubara, “Penggunaan Metode Failure Mode and Effect Analysis (FMEA) dalam Identifikasi Kegagalan Mesin untuk Dasar Penentuan Tindakan Perawatan di Pabrik Kelapa Sawit Libo,” J. VOKASI Teknol. Ind., vol. 3, no. 1, 2021.

M. R. Fernandi, “Analisis Kualitas Produk Minyak Goreng Kemasan Standing Pouch (STP) Menggunakan Metode FMEA (Failur Mode and Effect Analisys) PADA …,” vol. VII, no. 3, pp. 3646–3657, 2022.

E. P. Setiawan and N. B. Puspitasari, “Analisis Kerusakan Mesin Asphalt Mixing Plant Dengan Metode Fmea Dan Cause Effect Diagram (Studi Kasus: Pt Puri Sakti Perkasa),” Ind. Eng. Online J., vol. 7, no. 1, 2018.

A. Iswanto, M. Rambe, A. Jabbar, and E. Ginting, “Aplikasi metode Taguchi Analysis dan failure mode and effect analysis (fmea) untuk perbaikan kualitas produk di PT. XYZ,” J. Tek. Ind. USU, vol. 2, no. 2, p. 219330, 2013.

E. Rusmiati, “Penerapan Fuzzy FMEA dalam Mengidentifikasi Kegagalan pada Proses Produksi di PT. Daesol Indonesia.” Jakarta, Program Studi Teknik dan Manajemen Industri, Sekolah Tinggi …, 2011.

B. Nurlailah, S. Dedy, and A. Chani, “Penerapan Metode Failure Mode Effect Analysis (FMEA) Dan Expert System (Sistem Pakar),” J. Online Univ. Trisakti, 2016.

R. Riswan and P. Renosari, “Pengendalian Kualitas dengan Metode Failure Mode And Effect Analysis (Fmea) untuk Mengurangi Cacat Produk pada Hasil Produksi Grass Block Lubang Lima (Studi Kasus: Pt. Cisangkan-Cijerah) Pengendalian Kualitas dengan Metode Failure Mode And Effect Analysis (Fmea) untuk Mengurangi Cacat Produk pada Hasil Produksi Grass Block Lubang Lima (Studi Kasus: Pt. Cisangkan-Cijerah),” Pros. Tek. Ind., pp. 207–214, 2017.

I. Nurdiansah, Marno, and A. Santosa, “Analisa Kerusakan Mesin Bubut Al Pin 350 Dengan Metode Failure Mode and Effect Analysis (FMEA),” J. Ilm. Wahana Pendidik., vol. 8, no. 1, pp. 704–708, 2022, doi: 10.5281/zenodo.5921782.

N. Badariah, D. Sugiarto, and C. Anugerah, “( FMEA ) dan Expert System (Sistem Pakar),” Semin. Nas. Saints dan Teknol., vol. 1, no. November, pp. 1–10, 2016.

B. S. Wijaya, D. Andesta, and E. D. Priyana, “Minimasi Kecacatan pada Produk Kemasan Kedelai Menggunakan Six Sigma, FMEA dan Seven Tools di PT. SATP,” J. Media Tek. dan Sist. Ind., vol. 5, no. 2, p. 83, 2021, doi: 10.35194/jmtsi.v5i2.1435.

B. Septiana and B. Purwanggono, “Analisis Pengendalian Kualitas Dengan Menggunakan Failure Mode Error Analysis (Fmea) Pada Divisi Sewing Pt Pisma Garment Indo,” Ejournal3.Undip.Ac.Id, 2018.

M. Basori and S. Supriyadi, “Analisis Pengendalian Kualitas Cetakan Packaging Dengan Metode Failure Mode and Effect Analysis (FMEA),” Pros. Semin. Nas. Ris. Ter. SENASSET, pp. 158–163, 2017.

N. W. A. S. Dewi, S. Mulyani, and I. W. Arnata, “Pengendalian Kualitas Atribut Kemasan Menggunakan Metode Failure Mode Effect Analysis (FMEA)Pada Proses Produksi Air Minum Dalam Kemasan,” J. Rekayasa Dan Manaj. Agroindustri, vol. 4, no. 3, pp. 149 – 160, 2016.

Anizar, “Manajemen Risiko K3 Pada Divisi Produksi Menggunakan Fmea Dan Rca Di Pt.Xyz,” Univ. Muhammadiyah Kudus, vol. 1, p. 3, 2009.

Downloads

Published

2023-02-19

Issue

Vol. 20 No. 2 (2023): June 2023

Section

Articles

License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License

 

Copyright Notice

An author who publishes in the SITEKIN Journal agrees to the following terms:

  • Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-ShareAlike 4.0 License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal
  • Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgement of its initial publication in this journal.
  • Author is  permitted and encouraged to post his/her  work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See The Effect of Open Access).

Read more about the Creative Commons Attribution-ShareAlike 4.0 Licence here: https://creativecommons.org/licenses/by-sa/4.0/.